Discuss TurboSIM - The definitive guide at the Turbo-, Supersim and Simcloning Solution - Hackint0sh.org; Originally Posted by Cracker
How did you go with the at&t sim physical ...
I had no problem with the physical contacts on the AT&T Sim - worked fine in the iPhone as well as the nokia, with no issue - so basically I chopped the AT&T SIM, put it with the turbo SIM into the nokia, programmed it, then chopped my voda sim and put it all into the iPhone.. then changed the APN in the settings application and it just worked. I didn't need to deactivate/reactivate at all (I'd previously hacked the activation with the AT&T SIM, NOT the Vodafone one).
Originally Posted by Cracker
As for cutting it, I used a really sharp stanley knife. Rather than trying to cut it all in one go i did a succession of smaller cuts, to make sure there wan't too much pressure trying to split the plastic. I also cut a little smaller than needed, then shaved extra plastic off the SIM to make sure it fit snugly with the turbo SIM in the holder.
Vodafone use either COMP128v2 or v3 - not sure which, but definitely not v1. But that is irrelevant to this method, as encryption requests go straight to the SIM.
I've also had a few requests asking how I uploaded the code using the 6320i, so here goes:
1) Cut your AT&T SIM, and fit it with the turbo sim in the nokia
2) Download applesaft from http://www.bladox.com/pub/applesaft-0.92.tar.gz , and the cable utils from: http://www.bladox.com/pub/turbo-cabl...s-0.7.0.tar.gz . Extract the files into a folder, and drop applesaft.trb from the bin/ folder in the applesaft archive into the bin-win32 folder from the turbo cable utils folder
3) Use bluetooth to pair the phone with your computer (or use a cable)
4) In the bluetooth settings, look for the COM port that got mapped to 'COM1'/Serial on your phone (Its the one thats not labeled as PC Suite)
5) CD to the bin-win32 folder in a command prompt, and run 'turbo-app -dx applesaft.trb' (replace the x with the number of the COM port, i.e -d8 for COM8)
6) Wait for the info to be loaded, make sure there are no errors. If there is, try to identify and try again
7) Go to the 'Turbo' menu on the nokia, then to applesaft, and then set to set the IMSI
8) You can now remove the turbo sim from the nokia, set it up with your carriers sim, and put it in the iphone.
9) Change the APN in the Settings application on the phone/General/Network/EDGE to suit your carrier
Also, you can do it on the phone itself if you have SSH installed - details here: http://www.bladox.com/forum/viewtopi...=asc&start=195
confused with activation: which methods work?
Hi, sorry for the apparently silly question, but it really is not clear to me which kind of activation is required for the turbosim to work correctly. For instance I know of two different kinds of activations:
-DVD Jon's fake server (the one on windows that requires to modify iTunes);
-Anderson's command line utility for mac (the one I used, just a simple command from the Terminal when iPhone is connected via USB and iTunes is not modified at all).
Will the activations described above be ok towards using Turbosim? What about other kinds of activations that I don't know about?
Thanks to anybody who can answer clearly to this question.
I could be wrong, but I don't think the activation method matters - as long as the IMSI matches the AT&T SIM you use to set turbosim/applesaft up with.
Originally Posted by italianjob
For the record, I used Anserson's method, and it worked fine.
This is one of the key questions, and nobody seems to give a satisfactory answer. Many people simply refer to hacktheiphone.com, which is rather silly and obviously quite useless, since it lists 7 different methods on the site.
Originally Posted by italianjob
I now know that the activation you previously used must not brick the radio. I believe the official AT&T activation way is one. How about iASign using the AT&T SIM's ICCID? What happens if you use a pre-patched lockdownd?
Perhaps you meant the activations method AFTER inserting the SIM? How about before? Was your phone de-activated before you port your SIM over, or was it already activated (using anderson in your case), and you never had to de-activate it.
Originally Posted by linc
I don't believe any activation method 'bricks' the radio - they fool with the software on the phone, not in the baseband. I could well be wrong though, can anyone provide more info on this?
Originally Posted by p9939068
Also the iASign and anderson methods seem to be similar (the same? generating a activation record signed with a new certificate).
Actually now I look at it, I used the iASign method - with the AT&T SIM that came with the phone itself, then used that SIM to load the IMSI into the Turbo SIM. No activation was required after after inserting my carriers SIM with the turbo sim - i'm assuming the imsi was read at boot (which would have returned the at&t imsi), and then it stopped checking
As for the patched lockdownd, i don't know what would happen - but worst case, you could replace it with the original then use iasign.
I also still have not found a solution for my problem:
I have no original ATT card (No it's not in the SIM Holder)
I CAN do the following:
- Place the turbo sim on my non-att card
- Run applesaft via SSH on the Iphone and the NEW ISA app found on bladox)
- Change ICCID (Is stated on the iPhone Purchase BOX)
- Change IMSI (to a custom one, only first digits are required)
Partially unlock the iPhone to use the ATT custom ICCID and IMSI that i used. (In other words another NON-IPhone ATT/Cingular SIM)
Any chance that this will work?
p9939068: Since i am using windows, the method that works for me is http://www.hacktheiphone.com/iphone_...dding_mac.html (Stage 1) and http://www.hacktheiphone.com/iphone_...r_windows.html (Stage 2). If you use Mac choose the appropriate method that you are comfortable with. The end result is the same: activate the iphone.
I doubt these activation method would "brick" the iphone. Come to the worst just restore the firmware.
My iphone has been activated prior to the TurboSIM method using the ICCID of the included AT&T sim card.
Just to be clear:
This requires you to *cut* both the AT&T sim and your providers sim so they can fit into the TurboSim?
Does this make those two sims unusable as regular sims afterwards? So if this goes south, the At&T sim is broken?
ozbimmer please help!!!
I am sitting here in Ireland with the Turbo Sim and have got as far the chmod part but have no idea what to do next. How do get it to execute?
I dont understand the part where it says "chmod a+x" etc??
By djpav in forum Free Toolchain Software (Cydia App's)
Last Post: 04-22-2012, 07:31 PM
By Tucson Raider in forum Tutorials
Last Post: 03-14-2010, 08:06 PM
By MetalRat in forum Turbo-, Supersim and Simcloning Solution
Last Post: 01-09-2008, 01:35 PM
By hubbards in forum General
Last Post: 10-02-2007, 11:11 AM
By smersh in forum General
Last Post: 09-10-2007, 07:02 PM