Page 2 of 2 FirstFirst 12
Results 11 to 12 of 12
Discuss Open up an SSH command terminal and enter the following command: turbo-in at the Turbo-, Supersim and Simcloning Solution - Hackint0sh.org; -sh-3.2# turbo-iphone-smsreset Turbo Sim SMS Reset Utility for the iPhone -- Copyright 2007 iZsh Credits: ...
  1. #11
    Senior Professional Array

    Join Date
    Aug 2007
    Posts
    256
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    19

    Default here we go again....

    -sh-3.2# turbo-iphone-smsreset
    Turbo Sim SMS Reset Utility for the iPhone -- Copyright 2007 iZsh

    Credits: gruffy for discovering the root cause, iZsh
    and special thanks to Zf and #iphone-turbosim for all the
    support and help while tracking this problem down.

    * Leet Hax not for commercial uses
    Punishment: Monkeys coming out of your ass Bruce Almighty style.

    Reading the SMS list (AT+CMGL)... ERROR while executing AT+CMGL.
    -sh-3.2#

    anyone no what it is - have contact - because i could enable / disable comm


  2. #12
    Senior Professional Array

    Join Date
    Mar 2007
    Posts
    284
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    23

    Default

    Ok, These are the GOLDEN rules / pre-requisites to distinguish whether you have good contact or not. If you don't know you have good contact, you are wasting you time even being in the SSH session!

    The FIRST thing you should do is make sure your iphone is ACTIVATED and PAIRED with just the AT&T sim in the iPhone. Either do this with the patched Lockdownd file (recommended) or use iActivator or similar tools to activate the phone with the AT&T sim.

    If you've done this successfully, your phone should show 1 signal bar in the in the top left hand corner or it will display "No Service" after it has done certain actions like when its finished searching and failed to lock onto a network or if you have tried to make a call etc.

    When you put the at&t sim in with the turbosim and before you have disabled commcenter, your phone should still report 1 signal bar or no service!!!!!!!

    If it say's "no sim", you still have a contact problem!

    If your getting "No Service", check the menu Settings > Phone
    see if there is any menu option between SIM PIN and AT&T Services.

    If your getting "No Service", this is good, because it means your turbosim and AT&T sim have a good contact because the iphone is seeing the AT&T sim through the turbosim which is as it is supposed to do.

    Now you can proceed to try and program the turbosim.

 

 
Page 2 of 2 FirstFirst 12

Similar Threads

  1. [Terminal] sudo command in terminal
    By Jailbreak'r in forum General
    Replies: 6
    Last Post: 03-26-2008, 05:14 AM
  2. Build a one-click app from a command line command?
    By merl in forum Free Toolchain Software (Cydia App's)
    Replies: 2
    Last Post: 11-19-2007, 07:43 PM
  3. How to enter DFU mode thru command or API call?
    By vijay in forum Free Toolchain Software (Cydia App's)
    Replies: 1
    Last Post: 10-17-2007, 08:12 PM
  4. shut down command from terminal??
    By iPhoneLondon in forum General
    Replies: 1
    Last Post: 09-08-2007, 03:42 AM
  5. 1.0.2 - Command line exits on command
    By phattie in forum General
    Replies: 0
    Last Post: 08-24-2007, 12:33 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 11:12 PM.
twitter, follow us!