Discuss Problems with installation, don't pass the darwin part (tried 5 DVDs already) at the Tiger - Hackint0sh.org; Did you try another distro, try the latest one, iatkos v5i or ideneb, try this ...
Did you try another distro, try the latest one, iatkos v5i or ideneb, try this ogliatrino.
When darwin appear type:
HP Pavilion Elite m9250f
Snow Leopard 10.6.6, Asus IPIBL-LB MOD BIOS, Intel Quad Core Q6600, 4GB RAM (800mhz), 2x500GB, nVidia 8600GT (Works), ALC888S (Works), Wireless RT73 (Works), LAN (Works) - How to Install
- Hardware Combos
- FAQ by TJ2K7 Macbook Pro 13" iPhone 4
Follow meh: @icchansan If you just want to support hackint0sh.org with a donation click here
News: Downloaded JaS 10.4.8, kalyway 10.4.10 and xxX 10.4.11 Rev.2
XXX I don't even make a disc, apparently I read wrong and this don't support AMD.
JaS and kalyway don't restart my computer, but also don't show the installation screen. With some flags they freeze in the apple screen, like iAtkos, in others they freeze in a text screen. Tried the command "cpus=1 -v -x" with all my DVDs, the same restart; the iAtkos, the JaS and the Kalyway (tiger) freezes in text messages. I will link the images below.
The interesting is that iAkos and JaS show different messages each time, some times stop in different lines, varying the numbers show in the USBF: xx.xxx (last lines).
The Kalyway show the same error: "couldn't alloc class "IOUSBUserClientInit""
And thanks for the help so far.
Best regards, Rafael.
News: I still don't give up on having a Mac in my PC, but I'm experience a Mac right now, with a Virtual PC! The speed is terrible, the screen don't extend to the entire monitor and I'm having problems with the keyboard (I intended to write this in Safari, but my Backspace button don't stop pressing), but is a start. I read something about installing the Mac in the PC by Virtual Machine, I will try this today and post the results. Rafael.
Ok, tried and installed Mac tiger by VMware Workstation. I formated a Partition an all in the Mac format. Prepared the dual boot by chain0, all ready... But it doesn't boot! All installed, get the screen saying: installation concluded, restart your computer. You know, for for the first boot that leave you to the register screen? But it didn't happen! It still freezes in the Apple screen, no spinning circle at all. Now I'm losing hope, I'm accepting that is impossible to run Mac in this computer. Anyone knows what the reason of non-spinning/load apple? If not, please, what I need to change in this machine? Motherboard, processor, HD, all, what is the problem?
Thanks for the help.
iDeneb v1.3 successfully installed...
After it finishes, it asks me to reboot, then appears the screen with the apple for some seconds, then it tells me too reboot with the linked screen..... As soon as I get it, I'll try iAtkos v5..... meanwhile, any suggestions? Did I mistake something?
Last edited by ogliastrino; 02-02-2009 at 05:44 PM.
I can't complete install with kalyway 10.5.2 disc.
goes through boot. foes to apple install I do the disk utility and complete install. then when it restarts it hangs up. I'm trying again now to try and get it to take. I have an hp a1410n with a amd. please helpppppp
By kabik in forum Installation
Last Post: 03-30-2010, 02:56 PM
By dotFallen in forum Installation
Last Post: 05-06-2009, 09:58 PM
Tags for this Thread