Results 1 to 3 of 3
Discuss Need Help with Netgear GA311 on 10.6.0 at the Kernel / Kext (Driver) Support - Hackint0sh.org; Hey All, I have two drive dual boot hackintosh with Kalyway 10.5.2 on one drive ...
  1. #1
    Newbie Array

    Join Date
    Mar 2007
    Posts
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default Need Help with Netgear GA311 on 10.6.0

    Hey All,

    I have two drive dual boot hackintosh with Kalyway 10.5.2 on one drive and 10.6.0 (myHack/USB retail) on the other. Kalyway works perfectly but I am having Ethernet problems on SnowLeopard.

    I bought a Netgear GA311 as it was specifically recommended for working OOB on leopard/snow leopard. It works fine in Leopard (DHCP, etc), but in Snow Leopard it is recognized,but it will not get a DHCP address. I have tried assigning a manual IP from Network settings as well as from the Terminal with both ifconfig/route and ipconfig. It will come up and let me ping it self but nothing else on my network...like the router.

    Has anyone had any luck with this card Netgear GA311 on 10.6.0?

    lspci -v says

    Code:
    05:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
    	Subsystem: Netgear Unknown device 311a
    	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16
    	I/O ports at 1000
    	Memory at f3200000 (32-bit, non-prefetchable)
    	Capabilities: [dc] Power Management version 2
    I am thinking this has to be a driver issue?

    Thanks,
    Bill



  2. #2
    Newbie Array

    Join Date
    May 2010
    Posts
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default Need Help with Netgear GA311 on 10.6.0

    Having same problem...you ever get it to work?

    Thanks.

    Jason

  3. #3
    Newbie Array

    Join Date
    Jul 2009
    Posts
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Yes GA311 works with Snow Leopard 10.6.6!
    But it must show up as en0 en NOT en1. Otherwise it will not work!
    And delete all network prefs in "System Preferences ->Network" (left column) and make new ones.

    Type in terminal: ifconfig
    See for yourself:
    Code:
    en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    	ether 00:xx:xx:xx:b2:3d 
    	inet6 fe80::21a:4dff:fe56:b23d%en0 prefixlen 64 scopeid 0x5 
    	inet 192.168.1.2 netmask 0xffffff00 broadcast 192.168.1.255
    	media: 1000baseT <half-duplex> (1000baseT <full-duplex>)
    	status: active
    Used kexts: RealtekRTL81xx.kext RTL81xx OS X Driver [Lnx2Mac's Blog]
    Thanks for that lnx2mac

 

 

Similar Threads

  1. Netgear GA311 and Kalyway 10.5.2 Not Working
    By stidrvr in forum Kernel / Kext (Driver) Support
    Replies: 0
    Last Post: 01-19-2011, 07:23 PM
  2. Driver Netgear WG111 v2
    By nurdiesge59 in forum Hardware
    Replies: 0
    Last Post: 07-06-2010, 08:10 PM
  3. Netgear ga311
    By ollyclio in forum Installation
    Replies: 2
    Last Post: 12-16-2009, 02:13 AM
  4. neTGEAR GA311
    By ollyclio in forum Installation
    Replies: 0
    Last Post: 11-26-2009, 04:21 PM
  5. Losing/Changing IP address, Netgear GA311
    By cowhelmet in forum Hardware
    Replies: 4
    Last Post: 10-15-2008, 06:17 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 09:19 PM.
twitter, follow us!