Discuss You people do not help newbz here at the iPhone "2G" (Rev. 1) - Hackint0sh.org; All story is, i upgrade and downgrade my iphone 28 times in 1 week but ...
You people do not help newbz here
All story is, i upgrade and downgrade my iphone 28 times in 1 week but no use
i upgraded to 1.1.1 downgrade to 1.0.2
install BSD subsystem, openssh, terminal
apply these commands
mv /var/root/Media /var/root/Media.old
ln -s / /var/root/Media
upgrade to 1.1.1
i apply these commands using iphuc-jailbreak.exe
putjailbreak rdisk0s1 /dev/rdisk0s1
getfile /etc/fstab fstab
i open the fstab file and i found "rw" both lines
which means i am rw access to my iphone.
then i run
and i got the whole part completely accurate
i also run the iphoneinterface.exe for this command
after that in tutorial it says that i can now have access to ssh
but when i connect to iphone using WinScp
i got this msg "network error: connection refused"
and when i apply this command
then also i cant access to ssh .
and i am using this tutorial
all i need to connect to iphone using WinScp
for your help
I ping my iphone ip (192.168.0.98)
I deleted 4 files
i also use putty (cannot connect same problem)
i am using wifimax
and i just need to connect to SSH using WinScp which i cannot login please help me
try to use putty to access your ssh instead. BTW makesure your router setting is correct, try to set your iphone to static by manually assign an IP address to the phone
i am guessing you are using windows
once your baseband in 04.01.13_g
power off iphone with AT&T card
turn on itunes
plug phone into PC
when grey apple comes up, hold power & home for 10 seconds, let go power, hold home for 15 second more
restore in itunes should be prompted - say ok
shift restore to 1.0.2 (downgrade) find teh file on your PC
you will get error 1101 (thats ok)
run apptapp, errors,
open itunes, close itunes
run apptapp again hopefully no error
run pacay activation file
IBrickr -> BSD subsystem & Community Services
Ibrickr -> AnySim v1.1
Run AnySim with NEW SIM CARD IN PHONE!!!!!
remove AnySim with iBrickr
that wull give you 1.0.2 firmware and 04.01.13_g baseband, will work fine..
or i would suggest getting access to a mac and run indepandance 1.2.3/4 and going ot the help file and follow the instructions
the reason no one answer newbs questions cause its easily searched for, and not everyone has had afew drinks tonight and feels like regurtitating info all over the forum
ok i am one more question
as you seen the website
what i put DEVICE ID?
IMEI no (as i know)
what to put in ICCID ?
i entered the SIM ICCID but the website give me error
my sim ICCID is too much small
its about 12 characters
can anyone help me out from it,
all on the back of the box and iphone
but in tutorial it says
that enter the SIM ICCID
and you are telling me the back of the iphone box
what to do now ?
By ak786 in forum iOS 4.x (iPhone OS 4.x)
Last Post: 12-07-2010, 04:52 PM
By avestavik in forum Distributions
Last Post: 07-15-2009, 09:39 PM
By teddie in forum iPhone "2G" (Rev. 1)
Last Post: 01-25-2008, 07:04 PM
By breyton in forum General
Last Post: 09-11-2007, 07:46 AM