[1.1.2OTB GUIDE]**How to fix And Geounlock Problems, And some TIPS!!!
Ok, I don’t really know if this guide will help you out. So do it at your own risk. This is for Bootloader 4.6
This should help if you have bricked your phone in other way too.
Ok, first off all, despite all of the problems GeoHot did an unbelievable job. I had a problem but I think it was cause I didn’t paid so much attention, and kind of freaked out when it crashed. So thanks a lot GeoHot for everything.
My problem was that I tried the manual version of the unlock. I downloaded the files through installer and used terminal to send the commands. When I did :
./gunlock secpack ICE04.02.13_G.fls my phone crashed. (this time it was on airplane mode, so I don’t really know why it crashed).
So when I restarted my iPhone, I always end up at Recovery screen.
So, to fix this problem or similar problem, this is what I did.
1 – Download itunes 7.6 at apple.com
2 – Download 1.1.3ispw. You can download it through itunes.
3 – Put your iphone into restore mode, (what I think it already is). If it isn’t, just press power button + home button together, until you see the cable and itunes logo.
4 – Open iTunes and click Restore. (Don’t need to hold shift since iTunes will get 1.1.3 from their server, but if you already have, then press Shift + Restore and select it, so you don’t need to download it all over again).
5 – After restoring, youll have an 1.1.3 WORKING iPhone.
6 – Download DFU - www.send$pace.com/file/93fx93 (change $ to s)
7 – Extract DFU folder to C:/
8 – Go to the start menu and click Run, and type the following:
Now hit OK, this will force your iphone into DFU mode. Now it should have a with screen.
9 – Now click shift restore on itunes and Select 1.1.1 file. (I did this restore twice, so its up to you.) Now itunes will say that your iphone is in recovery mode. Press OK.
10 – Get ibrickr 0.91, and press Boot the phone. The background of your iphone should turn red, and then boot up. If ibrickr doesn’t work, use 1.1.2 jailbreak.zip (Google it, and you should find) and press boot from recovery.
11 – Now unlock your iphone with *#307# method. I prefer i.unlock.no instead of jailbreakme.com. But this is up to you guys.
12 – After jailbreaking 1.1.1 install oktoprep.
13 – Now open itunes again, and click shift+UPDATE (not restore, UPDATE), and select 1.1.2 file.
14 – Now you should have a locked 1.1.2 iphone. If your iphone stay on recovery screen after the update, use 1.1.2jailbreak to boot from recovery.
15 – Now you have a 1.1.2 jailbreaked and working.
16 – Set auto-lock to never.
17 – Open installer, and add http://installer.iClarified.co.
18 – Install BSD subsystem under System category.
19 – Install GeoHot Unlock under iClarified category.
20 – Press ok, and it will begin the installation. If it crash in the middle, that’s ok, just wait 5-10minutes and it should reboot.(If it don’t, then start all over again).
21 – After rebooting, IF you have no signal, follow the other steps.
22 - You have to use BRICKTOOL now to have signal .
23 – Download bricktool www.send$pace.com/file/e0tpu9 (change $ to s)
24 – Using winscp copy this 3 files to /USR/BIN and change their permissions to 0755
25 – Install terminal from installer on your iphone, and then type
26 – Reboot you phone, and you should have an 1.1.2OTB or (1.1.3OTB) working with your Simcard.
If you liked this tuto, or got an unlocked 1.1.2OTB donate to who really diserves.
Thanks a lot GeoHot.