Results 1 to 4 of 4
Discuss iPhone 1.0.2 won't start up and showing command lines at the iPhone "2G" (Rev. 1) - Hackint0sh.org; Got 1.0.2 iPhone wanted to install BSD Subsystem and installer, but it didin't intall... Did ...
  1. #1
    Newbie Array

    Join Date
    Jan 2008
    Posts
    2
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default iPhone 1.0.2 won't start up and showing command lines

    Got 1.0.2 iPhone wanted to install BSD Subsystem and installer, but it didin't intall...
    Did a restore WITH 1.0.2 firmware and had to activate. Opened latest iBrickr and pressed Jailbreak. When iBrickr started to jailbrake iPhone kept restarting for 10 minutes. I disconnected it and tried again. Nothing.
    After that iPhone started to boot up like that ; http://www.youtube.com/watch?v=rwTOZovceJo

    Tried to restore 1.0.1, 1.0.2 but nothing. Even used iBrickr to fix it. Booting up with
    iBrickr: Screen turns red(which means everything is OK) but then comes the lines again.

    It's unlocked iPhone.
    What should I do?

    Thanks,



  2. #2
    Administrator Array

    Join Date
    Oct 2007
    Posts
    4,145
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    10

    Default

    Try this (note taken from an old old thread on how to JB and act. 1.0.2 written by Carlos).

    Open itunes. It will say it needs to restore your iphone. Hold the Shift Button and hit restore. Select the 1.0.2 firmware you downloaded above. This should take about 5 minutes(depending on pc i guess)

    6) Wait for everything to finish, and it is back on the activation screen.

    7) Close itunes. open up AppTapp. Click continue. Select 1.0.2. Hit continue.
    ****this is very important... i have seen were AppTapp hangs...it will say that it is copying files, but never does, or it will go thru it very fast...3 seconds or so, and says it is done...IT IS NOT. The way you can tell it actually works is if your iphone restarts and goes to the yellow triangle screen, then back to the activation screen.***(Also... AppTapp will complete, but the status bar won't be all the way over to the right. This is fine, just a bit of bad coding.)

    8) Close AppTapp. Open PAYCAY, run the (CLICK HERE) activate.bat. it will start to copy files to your iphone. it will also activate your itunes. Follow the instructions on the screen...when it tells you to restart your phone turn your phone off(red slide). Leave it off for about 15 seconds, turn it on. you should now see the springboard(not the Waiting for activation screen). ( I have had some questions about the Lockdown file being replaced... if you wacth the script run, you will see it do it for you.)

    9) Open iBrickr. Click applications. Install the installer.pxl. follow these instructions on screen very carefully...you will have to completely restart your iphone twice during this process.

    Note: When you open ibrickr, there is a link that says applications.
    It will take you to a new screen that tells you to install the installer.pxl

  3. #3
    Newbie Array

    Join Date
    Jan 2008
    Posts
    2
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Thanks for your reply !

    But I don't get to the Activation screen. My iPhone shows Apple logo then a black screen with scrolling lines.
    Then it restarts and does it all again. I can get to recovery mode, but restoring with 1.0.1 and 1.0.2 does not fix that problem

  4. #4
    Administrator Array

    Join Date
    Oct 2007
    Posts
    4,145
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    10

    Default

    run itunes, connect to phone, hold power+home at the same time, phone will restart, when you see the apple, let go of power and continue holding home. the phone will enter DFU (yellow triangle) mode and itunes will prompt for recovery. You hit shift-click restore and select the 1.0.2 firmware image.
    When done, your phone will be like taken out of the box ... you can follow steps in post #2 (starting at #7)

 

 

Similar Threads

  1. Replies: 0
    Last Post: 06-29-2010, 10:10 AM
  2. Iphone F*cked nothing but command lines
    By djyoung in forum iPhone "2G" (Rev. 1)
    Replies: 2
    Last Post: 04-02-2008, 10:16 AM
  3. Replies: 6
    Last Post: 01-05-2008, 12:55 AM
  4. Replies: 10
    Last Post: 11-15-2007, 09:00 AM
  5. Open up an SSH command terminal and enter the following command: turbo-in
    By zincozinco in forum Turbo-, Supersim and Simcloning Solution
    Replies: 11
    Last Post: 09-02-2007, 10:58 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 08:02 PM.
twitter, follow us!