I just helped my friends and again the instructions work. I noticed the reason alot of peoples phone don't work is because, they rerun the anysim software again after it gets unlocked. There for taking away the sound and adding no service.

I have gone through so many steps and these works 100%

thanks

Originally Posted by cpyas

Guys, im using this to try and unlock but after restoring the software it says incorrect sim. is that right?

Yes it will lock but if you complete the process it will be fine

thanks mooshi for this tutorial!

Moshi Your the man!!!


Thanks.....

Works flawlessly thanks a lot man...

Good Job, I have fixed my Iphone, it is amazing solution....

Cooooooooooool, the short Solution work too.
throgh this method I fix my second Iphone

I have successfully unlocked my iphone.

However when i put my UK Vodafone sim card in, the signal fluctuated, often giving 'no service' and I wasn't able to make/receive calls. I put the sim back into my old phone, and it's not working fully there - so maybe a broken sim.

So I tried my wife's UK Orange sim in the iPhone. It seemed to work fine, but when the phone has been on standby for over a few minutes, it won't take incoming calls. I get a 'dead' tone on the phone I am calling from. Then I'll wake the iphone and calls will come in fine.

Is this the 'NO SERVICE issue'?

Hey thanks so much for this. I've tried it once now by issueing the two bbupdater commands in seperate commands, then followed the rest of the steps.

However, I'm not sure that this actually 'relocked' my phone. When I put a sim in there that was a NON-AT&T sim, it didn't report it as a bad sim.

Is there another way for me to 'relock' my phone again or am I doing something wrong?

Thanks again

ps. PLEASE HELP! AAHHHH

Here is the output from the first method:

(please assume all steps were taken appropriately, albeit through osx; activated and jailbroken after previous unlock and restore to 1.0.2)

# cd /
# cd /usr/bin
# chmod +x bbupdater
# launchctl unload -w /System/Library/LaunchDaemons/com.apple.CommCenter.plist
# bbupdater -e ICE03.14.08_G.eep
Preparing to flash using /dev/tty.baseband at 750000 baud
Please reset target
Resetting target...
ProcessDetailUpdated: Boot-loader is active
ProcessDetailUpdated: EBL version: 3.9_M3S2 3..9
ProcessDetailUpdated: Boot mode is: CC
ProcessDetailUpdated: Baud rate set to 750000
ProcessDetailUpdated: Get flash id.
ProcessDetailUpdated: CFI stage 1
ProcessDetailUpdated: Flash ID is: 88620089
ProcessDetailUpdated: CFI stage 2
ProcessDetailUpdated: Boot process finished
ProcessOutlineUpdated: Reading SW version data
Error: couldn't retrieve version information: File not found.
Upgrade from ??/ to ???/
Downloading EEP
ProcessOutlineUpdated: Start downloading from file ICE03.14.08_G.eep.
ProcessDetailUpdated: Sending sec-pack.
ProcessDetailUpdated: Load region 0
ProcessDetailUpdated: Sending end-pack.
ProcessDetailUpdated: Checksum OK.
ProcessDetailUpdated: Verify OK
ProcessOutlineUpdated: Process time was 1877 msec.
Resetting target...
Done
#

I tried the short and the long solution and nothing happened.
Just having NO SERVICE
Any ideas?
thanks

besalva, what phone network are you part of?

I'm having the same problem. I just tried the long portion now and this is the output:

# cd /
# cd /usr/bin
# chmod +x bbupdater
# bbupdater -v
Resetting target...
Error: Failed to initialize comm layer: (is it open by another app?)
Done
# launchctl unload -w /System/Library/LaunchDaemons/com.apple.CommCenter.plist
# bbupdater -v
Resetting target...
pinging the baseband...
issuing +xgendata...
firmware: DEV_ICE_MODEM_03.14.08_G
eep version: EEP_VERSION:207
eep revision: EEP_REVISION:7
bootloader: BOOTLOADER_VERSION:3.9_M3S2
Done
# bbupdater -e ICE03.14.08_G.eep
Preparing to flash using /dev/tty.baseband at 750000 baud
Please reset target
Resetting target...
ProcessDetailUpdated: Boot-loader is active
ProcessDetailUpdated: EBL version: 3.9_M3S2 3..9
ProcessDetailUpdated: Boot mode is: CC
ProcessDetailUpdated: Baud rate set to 750000
ProcessDetailUpdated: Get flash id.
ProcessDetailUpdated: CFI stage 1
ProcessDetailUpdated: Flash ID is: 88620089
ProcessDetailUpdated: CFI stage 2
ProcessDetailUpdated: Boot process finished
ProcessOutlineUpdated: Reading SW version data
Error: couldn't retrieve version information: File not found.
Upgrade from ??/ to ???/
Downloading EEP
ProcessOutlineUpdated: Start downloading from file ICE03.14.08_G.eep.
ProcessDetailUpdated: Sending sec-pack.
ProcessDetailUpdated: Load region 0
ProcessDetailUpdated: Sending end-pack.
ProcessDetailUpdated: Checksum OK.
ProcessDetailUpdated: Verify OK
ProcessOutlineUpdated: Process time was 1896 msec.
Resetting target...
Done
# Connection to 192.168.2.4 closed by remote host.
Connection to 192.168.2.4 closed.
gilligan-ms-macbook-pro-15:~ user$ ssh 192.168.2.4 -l root
root@192.168.2.4's password:
Last login: Thu Sep 27 17:43:08 2007 from 192.168.2.2
# launchctl load -w /System/Library/LaunchDaemons/com.apple.CommCenter.plist
#