Page 1 of 5 12345 LastLast
Results 1 to 10 of 41
Discuss AnySIM v1.1 AT+XSIMSTATE=1 **RESULTS** at the iPhone "2G" (Rev. 1) - Hackint0sh.org; I succesfully ran anySIM v1.1 on a 04.01.13_G baseband. The phone is now Unlocked and ...
  1. #1
    Senior Professional Array

    Join Date
    Aug 2007
    Location
    Brasil
    Posts
    111
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    12

    Exclamation AnySIM v1.1 AT+XSIMSTATE=1 **RESULTS**

    I succesfully ran anySIM v1.1 on a 04.01.13_G baseband.
    The phone is now Unlocked and Fully functional.
    Thanks Dev Team.

    Here are the results of:

    AT+XSIMSTATE=1
    +XSIM: 2

    +XLOCK: "PN",1,0,"PU",5,0,"PP",5,0,"PC",5,0,"PS",5,0

    What does "PN",1,0 means?

    For IPSF it is "PN",5,0 wich is Unlocked and Not Lockable, what about "PN",1,0?

    Greetings!



  2. #2
    Rookie Array

    Join Date
    Oct 2007
    Posts
    14
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Hey mate,

    how did you unlock ? AnySIM ? or step by step ?

    You recomend the IPSF app ? will it give final solution ?

    Thanks,
    Chura

  3. #3
    Senior Professional Array

    Join Date
    Aug 2007
    Posts
    134
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    14

    Default

    1=Unlockable
    0=Valid SIM

    What did you do exactly to run the xsimstate command because I try it and it doesn't do anything for me??

  4. #4
    Professional Array

    Join Date
    Sep 2007
    Posts
    91
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    11

    Default

    Actually I'm pretty sure that's the Unlock counter. 1 being unlocked, perhaps once.

    > 1 meaning it has been unlocked numerous times.

    5, leads me to believe that it's been unlocked and finalized.

    Speculation.

  5. #5
    Senior Professional Array

    Join Date
    Aug 2007
    Location
    Brasil
    Posts
    111
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    12

    Default

    ***bump***


  6. #6
    Senior Professional Array

    Join Date
    Aug 2007
    Posts
    134
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    14

    Default

    baalbeck, what did you do exactly to run the xsimstsate command in minicom?? I tried it and it doesn't do anything and check out the link below the address sounds crazy but it sttates what each value is

    simstate status

  7. #7
    Senior Professional Array

    Join Date
    Aug 2007
    Location
    Brasil
    Posts
    111
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    12

    Default

    Thank you apineflip! i bookmarked that one.

    Just run minicom, selecting the device as tty.baseband (rmember to shut down commcenter)
    type:

    AT+XSIMSTATE=1 [hit enter]

    it will show you all the info.

    By the way, it`s weird such SIMSTATE because the phone it is actually unlocked. How come PN is set as Unlockable?!

  8. #8
    Advanced Array

    Join Date
    Sep 2007
    Posts
    48
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    +XSIM: SS

    +XLOCK: "PN",X1,X2,"PU",X1,X2,"PP",X1,X2,"PC",X1,X2,"PS",X 1,X2(the only lock present is the PN lock)

    SS:

    0=No SIM Inserted

    2=SIM Ready

    6=SIM Busy

    X1:

    0=Unlockable(i assume without attempt counter)

    1=Unlockable

    2=Unknown(i have never seen this)

    3=Attempt Limit Reached

    4=Unlocked and Lockable

    5=Unlocked

    X2:

    0=SIM Valid

    1=Unknown(this gets set for PN when unlock is attempted)

    4=SIM Not Valid

    These values weren't found in any manual, and were all determined either empirically or by reversing the firmware.

  9. #9
    Rookie Array

    Join Date
    Sep 2007
    Posts
    11
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    How do you run minicom ?

  10. #10
    Advanced Array

    Join Date
    Sep 2007
    Posts
    48
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    So for your SIMSTATE,

    Using the new Anysim1.1 returns the phone in an strange "Unlockable" status,
    BUT Sim is valid and ready and NCK counter remains at 0.... the last part is a pleasant sign


 

 
Page 1 of 5 12345 LastLast

Similar Threads

  1. anySIM cannot unlock this phone. anySIM will now quit.
    By xevans in forum iPhone "2G" (Rev. 1)
    Replies: 5
    Last Post: 01-28-2008, 04:48 AM
  2. [Minicom] At+xsimstate
    By sudo-s in forum Tools
    Replies: 0
    Last Post: 01-21-2008, 09:44 AM
  3. Unlock Problem Anysim 1.1 --> Anysim 1.2u
    By maajka in forum iPhone "2G" (Rev. 1)
    Replies: 2
    Last Post: 11-21-2007, 01:58 AM
  4. Replies: 11
    Last Post: 10-31-2007, 09:07 AM
  5. anySIM 1.1 - Must have new SIM in iPhone while anySIM runs?
    By wildonrio in forum iPhone "2G" (Rev. 1)
    Replies: 0
    Last Post: 10-16-2007, 11:31 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 12:09 AM.
twitter, follow us!