Results 1 to 7 of 7
Discuss 1.1.3 unlock freaking great...but what if you have 1.1.1 OTB? at the iPhone "2G" (Rev. 1) - Hackint0sh.org; I've searched for hours but to no avail. so what if you have an unlocked ...
  1. #1
    Newbie Array

    Join Date
    Feb 2008
    Posts
    6
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default 1.1.3 unlock freaking great...but what if you have 1.1.1 OTB?

    I've searched for hours but to no avail.

    so what if you have an unlocked OTB 1.1.1? what are the steps to upgrade to 1.1.3 unlocked?



  2. #2
    Rookie Array

    Join Date
    Aug 2006
    Location
    Hungary
    Posts
    27
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Here is how from iphone.unlock.no

    How to jailbreak, activate and unlock iPhone with 1.1.1

    This tutorial assumes that your iPhone has firmware version 1.1.1. If you are unsure, here is how to check: On the emergency dial screen dial *3001#12345#* and tap Versions. Firware version should be 04.01.13_G. If it's 03.14.08_G you have v1.0.2 and need to update it to 1.1.1 first. Read here first if you previously unlocked your phone.
    Bypass activation and prepare phone for software installation

    1. Make sure you have a SIM-card with PIN turned off, and power on your phone (the supplied AT&T card works fine).
    2. On the activation screen, slide for emergency and dial: *#301# to make the phone call itself. (If the incoming call dialog quickly disappears but it keeps ringing, just dial 0 (remove *#301# first), and it will call itself)
    3. Answer the call, and tap on Hold
    4. Phone will call it self again, tap Decline. You will now be returned to the normal dialer.
    5. Tap on contacts, and tap the + icon to add a new. The only info you are going to add to this contact are two URL's. To add a URL, tap Add new URL. The first URL is prefs followed by a colon: prefs: and the second is i.unlock.no. Tap Save.
    6. Your contact now has two "web pages" - tap on the first one (prefs. This will take you to the settings dialog. The reason you want this, is because you need to connect to a Wi-Fi network, so tap on Wi-Fi, and get connected to a network, and make sure the icon on top of the screen is indicating that you are connected. While you are in the settings dialog, you should also set: General → Auto-Lock → Never.
    7. Now, press the home button, and again, slide for emergency dial 0, Answer the call, Hold and Decline the new call so that you get to the contacts. Tap on your contact (No Name), and this time tap on the other home page, i.unlock.no
    8. Safari will launch and show you a webpage. Tap on Tap here to jailbreak your iPhone
    9. Phone will return to activation screen and after a few seconds the phone should restart.
    10. If the phone does not restart after waiting a full minute, please make sure that you have your phone connected to the computer and try again.
    11. When the phone starts again, it should no longer say slide for emergency, but rather Slide to unlock It means it was successfull! Activation is now bypassed, and phone prepared for software installation! (If you are going to use an AT&T SIM, you won't need to do the next step.)


    Unlock the SIM-lock on jailbroken 1.1.1

    1. Open installer, and install the update if prompted.
    2. Go to sources and tap Edit and Add
    3. Add this URL: http://i.unlock.no
    4. Tap Done and then Refresh
    5. Go to Install (at bottom) and scroll down to the Unlocking Tools category and install AnySIM
    6. When installed you can press the home button, and you will find a new AnySIM icon on your home screen. Launch it and follow the instructions.
    7. The unlocking process will take about 5-10 minutes, in the end it should say it was successful!
    8. To clean up your phone, launch Installer and uninstall AnySIM. Then go to Settings → General → Auto-Lock and set it to a prefered value.

    Congratulations, you are done!


    Thats all

  3. #3
    Newbie Array

    Join Date
    Feb 2008
    Posts
    6
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Quote Originally Posted by Revengangel View Post
    Here is how from iphone.unlock.no

    How to jailbreak, activate and unlock iPhone with 1.1.1

    This tutorial assumes that your iPhone has firmware version 1.1.1. If you are unsure, here is how to check: On the emergency dial screen dial *3001#12345#* and tap Versions. Firware version should be 04.01.13_G. If it's 03.14.08_G you have v1.0.2 and need to update it to 1.1.1 first. Read here first if you previously unlocked your phone.
    Bypass activation and prepare phone for software installation

    1. Make sure you have a SIM-card with PIN turned off, and power on your phone (the supplied AT&T card works fine).
    2. On the activation screen, slide for emergency and dial: *#301# to make the phone call itself. (If the incoming call dialog quickly disappears but it keeps ringing, just dial 0 (remove *#301# first), and it will call itself)
    3. Answer the call, and tap on Hold
    4. Phone will call it self again, tap Decline. You will now be returned to the normal dialer.
    5. Tap on contacts, and tap the + icon to add a new. The only info you are going to add to this contact are two URL's. To add a URL, tap Add new URL. The first URL is prefs followed by a colon: prefs: and the second is i.unlock.no. Tap Save.
    6. Your contact now has two "web pages" - tap on the first one (prefs. This will take you to the settings dialog. The reason you want this, is because you need to connect to a Wi-Fi network, so tap on Wi-Fi, and get connected to a network, and make sure the icon on top of the screen is indicating that you are connected. While you are in the settings dialog, you should also set: General → Auto-Lock → Never.
    7. Now, press the home button, and again, slide for emergency dial 0, Answer the call, Hold and Decline the new call so that you get to the contacts. Tap on your contact (No Name), and this time tap on the other home page, i.unlock.no
    8. Safari will launch and show you a webpage. Tap on Tap here to jailbreak your iPhone
    9. Phone will return to activation screen and after a few seconds the phone should restart.
    10. If the phone does not restart after waiting a full minute, please make sure that you have your phone connected to the computer and try again.
    11. When the phone starts again, it should no longer say slide for emergency, but rather Slide to unlock It means it was successfull! Activation is now bypassed, and phone prepared for software installation! (If you are going to use an AT&T SIM, you won't need to do the next step.)


    Unlock the SIM-lock on jailbroken 1.1.1

    1. Open installer, and install the update if prompted.
    2. Go to sources and tap Edit and Add
    3. Add this URL: http://i.unlock.no
    4. Tap Done and then Refresh
    5. Go to Install (at bottom) and scroll down to the Unlocking Tools category and install AnySIM
    6. When installed you can press the home button, and you will find a new AnySIM icon on your home screen. Launch it and follow the instructions.
    7. The unlocking process will take about 5-10 minutes, in the end it should say it was successful!
    8. To clean up your phone, launch Installer and uninstall AnySIM. Then go to Settings → General → Auto-Lock and set it to a prefered value.

    Congratulations, you are done!


    Thats all
    thanks for the reply dude. But I already did those steps and have a 1.1.1 unlocked. I want to take it to 1.1.3 unlocked. i've read countless tutorials but they are all for 1.1.2/1.1.3 OTB (bootloader 4.6) unlocks.

    I am sure there are people out there who have an unlocked 1.1.1 and have taken it to 1.1.3

  4. #4
    Board Hero Array

    Join Date
    Dec 2007
    Posts
    1,044
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    74

    Default

    Quote Originally Posted by Gotham View Post
    thanks for the reply dude. But I already did those steps and have a 1.1.1 unlocked. I want to take it to 1.1.3 unlocked. i've read countless tutorials but they are all for 1.1.2/1.1.3 OTB (bootloader 4.6) unlocks.

    I am sure there are people out there who have an unlocked 1.1.1 and have taken it to 1.1.3
    Do the IPSF-style unlock (released by Geohot a few weeks ago), then upgrade through iTunes (the unlock is upgrade-resistant), then jailbreak+activate with Ziphone.
    iPhone 3GS / 3.1.2 JB (PwnageTool) / 04.26.08 carrier-locked, Carrier Logo Fixer / Cydia / 1000 posts on Hackint0sh

    Installing Cydia programs on a phone that has no internet connection: read this.

    Editing binary .plist, .strings, .nib and .xib files:
    * on your computer: Windows tool / conversion website.
    * on your iPhone: convert those files in a terminal with plutil (installed with Erica Utilities) or edit them with iFile (Cydia links).

  5. #5
    Newbie Array

    Join Date
    Feb 2008
    Posts
    6
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    Quote Originally Posted by Jim Danner View Post
    Do the IPSF-style unlock (released by Geohot a few weeks ago), then upgrade through iTunes (the unlock is upgrade-resistant), then jailbreak+activate with Ziphone.
    could you link me to it? i've found a bunch of these. i want to make sure i get the proper one =]


  6. #6
    Speedy Administrator Array n350z's Avatar

    Join Date
    Nov 2007
    Location
    United Kingdom
    Posts
    3,021
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    10

    Default

    Quote Originally Posted by Gotham View Post
    could you link me to it? i've found a bunch of these. i want to make sure i get the proper one =]
    Be careful with the IPSF unlock, its a great unlock but if you have a problem with wifi and you can't get the backup copy or don't back a copy of the seczone you're have a bricked phone if something goes wrong.

    Read Read Read before trying it
    -
    Read the stickies and search the forum before posting!
    Did we solve your problem? +1 us above
    If you want to become a Hackint0sh supporter click here
    ----------
    Follow Hackint0sh Follow Me

  7. #7
    Speedy Administrator Array n350z's Avatar

    Join Date
    Nov 2007
    Location
    United Kingdom
    Posts
    3,021
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    10

    Default

    Your second option with 3.9BL and less likely to go wrong if your new to unlocking is.

    1) Update to 1.1.3 with itunes
    2) use the ziphone -a -j
    3) From installer add anysim 1.3
    4) turn auto lock to never
    5) set airplane mode on
    6) run the anysim 1.3 app from springboard
    -
    Read the stickies and search the forum before posting!
    Did we solve your problem? +1 us above
    If you want to become a Hackint0sh supporter click here
    ----------
    Follow Hackint0sh Follow Me

 

 

Similar Threads

  1. any help would be great
    By MR.Winmac in forum Archiv (Leopard)
    Replies: 0
    Last Post: 03-02-2008, 06:08 PM
  2. Holy freaking crap, what did i do?????? How do i add installer.app?
    By ParamedicMXr in forum iPhone "2G" (Rev. 1)
    Replies: 1
    Last Post: 02-12-2008, 07:10 AM
  3. New at this... Any help would be great!!
    By Xep in forum iPhone "2G" (Rev. 1)
    Replies: 4
    Last Post: 10-01-2007, 06:38 AM
  4. The Great Unlock Race is On...
    By goodcompany in forum General
    Replies: 31
    Last Post: 08-31-2007, 07:45 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 03:37 AM.
twitter, follow us!