Discuss [1.0.2 OTB] Major Problems at the iPhone "2G" (Rev. 1) - Hackint0sh.org; I had a unlocked v.1.0.2 iphone but than I something happened to it and I ...
[1.0.2 OTB] Major Problems
I had a unlocked v.1.0.2 iphone but than I something happened to it and I didnt get any signals I went ahead and tried to upgrade it to v.1.1.1 but after doing that it just got all f***ed up. After restoring it to v.1.1.1 I try to slide the slider but it just freezes, I have unknown IMEi and ICCID, I tried to reoboot the phone with ibrickr but than it just messes up and I have to restore again. I tried restoring down to v.1.0.2 but it wont work. ON the activation screen it says "Repair Needed, iPhone cannot make or receive calls., www.apple.com/support"
Last edited by x0bry7x; 02-11-2008 at 05:28 AM.
From 1.0.2 . Before going up to any other versions you need to revirgin/virginize that 1.0.2 baseband.
go to http://i.unlock.no and read about virginize & 1.0.2 - that will take care of IMEI & ICCID.
When you are done. you can go to 1.1.1 --> 1.1.2 --> 1.1.3
bump same symptom but different circumstances - ran 1.0.2 unlocked and jailbroken for several months, just upgraded to 1.1.1 successfully using The Virginizer from installer app and then used iTunes to upgrade to 1.1.1 - used anysim 1.1 to unlock 1.1.1 firmware with my T-Mobile sim card again, everything working fine
then followed instructions on i.unlock.no to upgrade from 1.1.1 to 1.1.2 and installed OktoPrep
unfortunately, i think there was one additional step - maybe i needed to install BSD subsystem?
at any rate, after upgrading, came out of activation mode, but no wifi and no edge or phone service. the menu options on settings were a faded gray color and i was not able to access.
i tried several methods of downgrading to 1.1.1 and then 1.0.2 after that didn't work - each time the iTunes error message reading cannot be used with iTunes because the SIM card is not installed You must insert your SIM card into your iPhone in order to activate it.
finally, with iBrickr i was able to install 1.0.2 successfully and jailbreak, but i can only install apps through iBrickr and I cannot get out of the emergency screen reading "Repair Needed iPhone cannot make or receive calls. www.apple.com/support" . when i click on the little "i" button on the emergency screen, i get a pop up stating
iPhone cannot make or receive calls
did you virginize your 1.0.2 before upgrade to 1.1.1
anyway, now if fcuked up. u should download all 1.0.2, 1.1.1, 1.1.2 and 1.1.3 if you want to go all the way
put your iphone in DFU (hold Home and Power button trick) when connect to itunes and then Click Shift - Restore. choose 1.0.2 file
after that u should follow guide to Jailbreak it. Virginized it, Shift Update to 1.1.1
jailbreak at 1.1.1...Unlock if you want to stay at 1.1.1
if you want 1.1.2 then u don't need to unlock at above step. just install Optoprep and Shift Update to 1.1.2...
many guide in here.
or check at iclarified
any way to virginize using a pxl or something i can install from ibrickr? i installed installer app through iBrickr, but i cannot get out of the emergency screen in order to activate wifi or even to download virginizer on installer app.
Please start a new thread for yourself. It is hard enough to help one person. Your problem in this thread although similar but it is different.
Do that please.... Thanks
Your phone has a 3.9 Bootloader. You can pretty much do anything you want with it. Keep it simple. Don't go crazy and start "trying" things..
Last edited by dtube; 02-11-2008 at 10:11 AM.
anyway, choose a guide and follow it carefully
sometime when jailbreak or unlock u Have to let it do its things without touching your iphone.
when first upgrading from 1.0.2 to 1.1.1 i used installer app to install Virginizer and the upgrade to 1.1.1 was flawless. when i tried to continue on to go to 1.1.2 is when something f**ed up. but now i am not able to get out of the emergency screen, even restoring all the various firmwares from 1.1.1 1.1.2 to 1.0.2
right now i believe i successfully downgraded to 1.0.2 because iBrickr is telling me i have 1.0.2 now and it is able to pair with the phone and install software, also the DFU icon switched from the itunes/white cable logo to the yellow triangle logo, which reinforces the idea that i successfully downgraded to 1.0.2.
however, i'm not able to get out of the emergency screen in order to run any apps
ok dTube- sorry i'll start a new thread
By underwaterknifefighter in forum General
Last Post: 11-04-2011, 05:04 PM
By darkelfx89 in forum iPhone 3GS
Last Post: 12-17-2009, 10:24 PM
By syper in forum General
Last Post: 02-27-2008, 05:15 AM
By jtanner in forum General
Last Post: 01-28-2008, 12:46 AM