Results 1 to 4 of 4
Discuss kalyway 10.5.2 on ASUS M2A-VM -install workx, no first boot possible at the Installation - Hackint0sh.org; hello, i have setup a ASUS M2A-VM, with Kalyway 10.5.2 All drives/DVD on SATA, AHCI ...
  1. #1
    Newbie Array

    Join Date
    Jan 2010
    Posts
    2
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default kalyway 10.5.2 on ASUS M2A-VM -install workx, no first boot possible

    hello,

    i have setup a ASUS M2A-VM, with Kalyway 10.5.2

    All drives/DVD on SATA, AHCI enabled

    setup worx without any problems.

    At the first but there comes the apple on gray screen with the waiting wheel below, and nothing happens then.

    switched allready from AHCI to IDE etc., any ideas what i could do?

    thanks



  2. #2
    Professional Array

    Join Date
    Aug 2009
    Posts
    74
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    8

    Default

    I'll tell you what the smarter guys here will say...boot with -v and post what it stops on.

    I know from a HP laptop install that it would sit there like that for 10 or 15 minutes until it would boot to the desktop sometimes, annoying.

    And later found out that with that laptop I had to have a usb keyboard & mouse hooked up, that usually caused the boot process to be much faster...

  3. #3
    Newbie Array

    Join Date
    Jan 2010
    Posts
    2
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    i got it up and running with leo4all v3.

    but the display is just 1024x768, i am a noob with this, how can i change this settings now?

    thanks for help

  4. #4
    Professional Array

    Join Date
    Aug 2009
    Posts
    74
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    8

    Default

    Well, you are having the problem with your video because you don't have the right kext (driver) for your video card/chipset installed.

    There is a couple of different ways to fix this though but first you have to find out what your video card/chipset is.

    Once you find that out, you can use KextHelper to install it or use OSx86Tools to install it, either one in my personal opinion will work just fine. Then when you restart you should have the option in the system preferences to set your resolution. It will depend on what resolution your display supports as to what you're going to be able to set it at, whatever Windows option(s) you had should be supported in OSX once you get the right kext (driver) installed.

    You can also pop the DVD back into your drive and go back to the customize options and install the correct video Kext there. Make sure you uncheck the actual install of OSX if that distro supports doing so or you'll just install another install of the operating system.

 

 

Similar Threads

  1. Won't boot from Kalyway to install. NOOB needs help
    By sirdeltalot in forum Installation
    Replies: 1
    Last Post: 01-20-2010, 08:03 AM
  2. How to install kalyway to Asus P5B-vm
    By cae7225 in forum Installation
    Replies: 1
    Last Post: 05-21-2009, 07:36 PM
  3. Replies: 0
    Last Post: 05-06-2009, 09:18 PM
  4. [Kalyway] Won't Boot/Install
    By tempt11 in forum Archiv (Leopard)
    Replies: 3
    Last Post: 07-18-2008, 07:17 PM
  5. Replies: 1
    Last Post: 07-15-2008, 01:00 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 08:41 AM.
twitter, follow us!