Results 1 to 3 of 3
Discuss iAtkos L2 on HP Pavilion DV6-6160ew - installer cannot boot up at the General - Lion 10.7.x - Hackint0sh.org; Hi, I was trying to install iAtkos L2 on my HP Pavilion DV6-6160ew laptop, but ...
  1. #1
    Newbie Array

    Join Date
    Mar 2012
    Posts
    1
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default iAtkos L2 on HP Pavilion DV6-6160ew - installer cannot boot up

    Hi,
    I was trying to install iAtkos L2 on my HP Pavilion DV6-6160ew laptop, but there seems to be a problem. Every time I try to boot up the installer, it doesn't even start the installation. It only gets as far as the screen which says "Press any key to boot up...". If I do press a key, the progress bar stops and nothing happens(I waited a really long time). If I don't, the progress bar finishes and nothing happens. What can be the reason for this?

    Here are the specs:
    HP Pavilion DV6-6160ew
    Intel Core i7-2630QM
    Intel HM55 Express Chipset
    Intel HD Graphics + AMD Radeon HD 6770M
    IDT High Definition Audio Codec
    ethernet - Realtek PCIe GBE Family Controller
    wifi - Intel Centrino Wireless-N 1030
    SATA hard disk, IDE optical disk drive
    the hard drive has MBR, three primary partitions, one with Windows 7
    PS/2 touchpad and keyboard
    Last edited by pawcio1357; 03-28-2012 at 08:21 PM.



  2. #2
    Newbie Array

    Join Date
    Apr 2012
    Posts
    2
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Rep Power
    0

    Default

    I suppose you have a pc with windows and there the. Dmg iatkos l2, remember to record the image with nero or do not use TransMac ultraiso

    I tenog an HP and when you start preciono f9 to ask me So I boot device and select the optical drive there

  3. #3
    Newbie Array

    Join Date
    Apr 2012
    Location
    Bumbesti-Jiu, Romania
    Posts
    1
    Post Thanks / Like
    Downloads
    1
    Uploads
    0
    Rep Power
    0

    Default

    I have a different laptop than yours but with the same chipset ( HM55 ) and i installed iAtkos L2 with some degree of success ( there is no kext/driver for my wirelles ( atheros 9485 ) and graphics - Intel HD Graphics from i3 processor Arrandale ) . If you had resolved the problem of booting from DVD / USB like the above user tell you or 'read the f... manual' there will be (maybe) some problems witch you may encounter .
    For my i3 380m processor i have resolved these with : busratio , cpus , -v , npci . My install process was : first I burned iAtkos dmg file from windows on an USB stick ( larger than 4 GB ) with Transmac - free for 15 days . I also ave a DVD with iATkos created with nero from dmg file , but USB is much faster and easier to use. Once this is done you must start your HP and select to boot from USB or DVD respectively. Then you must stop the automatic bar / countdown of booting by pressing any key . You can now run the installation and kernel ( default mach_kernel ) with parameters . For me , on this phase , mandatory was : cpus=1 busratio=19 . For you busratio=20 . You can also put -v as a parameter for verbose mode...
    If all is good you will get , eventually ( for me was a 4 minutes process ) into graphical installation mode. Since I don't have a discrete graphic card , only the intel HD Graphics I can not tell you to install or not drivers for ATI but i recommend to install only drivers for PS2, USB , none for graphics or network . You will have plenty of time to do that later. Let the bootloader install by default .
    Ok, you must successfully complete the installation ( with confirmation screen ).
    since you have windows also installed , on next boot please chose windows . Now in windows you can see files on mac partition with mac drive ( Mediafour Corporation ) and delete from /System/Library/Extensions all kext with name like appleHdGraphics . Now you can boot into iatkos lion if you write this cpus=1 busratio=20 -v npci=0x2000 as parameters for kernel .
    Eventually you will have a graphic interface of 1024*768 , configure your user account , install new kext for graphic card ATI , sound, network etc etc etc
    You can put parameters in /Extra/org.chameleon.Boot.plist search with google for that ...

 

 

Similar Threads

  1. Replies: 0
    Last Post: 08-30-2011, 03:15 PM
  2. [HELP] HP Pavilion dv7-2140eo iAtkos v7
    By syQ in forum Installation
    Replies: 1
    Last Post: 09-19-2010, 06:10 AM
  3. iATKOS S3 Installion on HP Pavilion
    By UT8F in forum Installation
    Replies: 1
    Last Post: 06-19-2010, 07:47 AM
  4. IAtkos v7 and Hp pavilion 6675ep
    By braga in forum Installation
    Replies: 0
    Last Post: 10-30-2009, 02:46 AM
  5. iATKOS v7 10.5.7 wont boot on HP Pavilion DV2818ca
    By moekaz8 in forum Installation
    Replies: 0
    Last Post: 07-31-2009, 01:31 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin®
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Search Engine Friendly URLs by vBSEO
(c) 2006-2012 Hackint0sh.org
All times are GMT +2. The time now is 09:36 AM.
twitter, follow us!