how long your batery hold in average use?
how long your batery hold in average use?
So guys, updates.
I restored to 1.1.3 and unlocked with Ziphone, and I'm glad to report I still have no problems. But the thing is, before restore, the last time I synced my iPhone, my Powerfilemanagement file was still deleted, so maybe when I backed up my phone back to its original settings, it deleted the file again? would that be possible. Battery life doesn't seem great though, so that's why I have my doubts, though it could because I raped the battery when I had this problem.
Either way, I'm quite happy. :]
I have a similar prob ! i tried restoring 1.1.4 thru Zibris 2.5 b ver but still no sucess :( . My had 1.02 jb but now m on 1.1.4 jb, unloacked n activated thru Zibri 2.5b, BUT -
My phn doesn ring in sleep mode !
My phn doesn hav WiFi (No Wifi Prob) !
My phn doesn hav Bluetooth !
My phn's Batt drains out very quickly when it is around 40-35 % !
Does ne 1 hav ne kind of soln 2 these prob ?????? :-(
I'm going to count my history. I had the same problem that all the
other, amd it has been solved to me with the new update. My telephone was a
1.1.2 OTB, I liberalized it to the traditional form, with iNdependence
and unlock of Geohot for 1.1.2.
I have had the problem of not receiving calls in sleep mode, and i did need to
use iMapldle so that the telephone sounded.
In the end the following thing has been solved to me the problem:
- Recover the telephone with iTunes to the 1.1.2
- Downgread the bootloader with Ziphone 2.5 from the 4.6 to the 3.9
- Recover the telephone with iTunes to the 1.1.4
- Active, Jailbreak and Unlock with Ziphone 2.5
Now the telephone works to me of correct form, EVERYTHING!!!. The
calls, wifi, bluetooth, etc. I hope that it also serves you.
I've been following this thread for a while and finally got my girlfriend's phone working right!
She has 1.1.2 OTB.
She first used stealthsim and was having no incoming calls when in sleep mode.
Then when geohut's unlock for 1.1.2 came out, we tried it and her phone kept having the same problem.
When 1.1.3 came out, we unlocked it using ziphone (but without downgrading bootloader to 3.9). It worked for a few hours and then the problem came back.
Finally, Restored the phone in itunes to 1.1.4, used newest ziphone with downgrade of bootloader... it's been 3 days without any dropped calls!
Hope this works for you!
I got the same problem and among others in this forum I discovered that it is in my case fully due to Navizon (version 2.0.1). Even if you don't start the client program Navizon after a reboot of the iPhone, Navizon is spawning a daemon at boot time. This daemon is always active in memory (therefore it is a daemon ;-) ). I think this one is responsible for shutting down the SIM or whatever after a couple of minutes in Standby. I see also very much Crashreports in /var/logs of the Baseband program. In that logs there is much crap I don't understand, but one thing is crystal clear:
Reason: modem reset
After deinstalling Navizon the problem is over immediately (after reboot).
I will send a report to Navizon about this and hope they come up with a next version soon.
I have the same sleep mode/no call problem. Installing the imapIdle works!! thanks to the guy who discovered the trick. no luck with johntool, downgrading baseband etc. just have to check out how long battery life last next....
a quick update from me.
i was trying to find a solution for " no service / low singnal / sleep mode no calls " problem but didn't want to downgrade the baseband with Ziphone.
so i went on and software downgraded the baseband (guidance is sticky in software unlock section).
currently iphone shows full network converage which is unusual. all bars are on.
i will put it in a sleep mode and advise if this cured the problem.
I got the same problem.
I suspect it is related to eeprom error. Try to use ziphone(do one step is enough, activate) if you want to check for this error. Then, you will get some quick error message like below :
AppleMRVL868x: Reading EEPROM data
AppleMRVL868x: Invalid calibration data in device tree
This eeprom stores powersafe and another 4 functions( 3 or 4 i forgot).
To solve this problem....
bbupdater -e eeprom.eep