Ok I have a retail install of Snow Leopard on my MSI Wind U100 Plus and need some drivers. I need Headphone, Line in, bluetooth, webcam and mic. Then I have a full working Hackintosh and I can update from software update!

Here are my specs:

Hardare tab:
Hardware Overview:

Model Name:Mac
Model Identifier:U90/U100
Processor Speed:1.67 GHz
Number Of Processors:1
Total Number Of Cores:1
L2 Cache:512 KB
Memory:2 GB
Bus Speed:667 MHz
Boot ROM Version:MBA11.00BB.B00
SMC Version (system):1.30f3
Serial Number (system):CK034KMHK5B
Hardware UUID:00000000-0000-1000-8000-000000000000

Graphics/Displays:
Intel GMA 950:

Chipset Model:GMA 950
Type:GPU
Bus:Built-In
VRAM (Total):64 MB of Shared System Memory
Vendor:Intel (0x8086)
Device ID:0x27ae
Revision ID:0x0003
Displays:
Display:
Resolution:1024 x 600 @ 75 Hz
Pixel Depth:32-Bit Color (ARGB8888)
Main Display:Yes
Mirror:Off
Online:Yes
Built-In:Yes
Display Connector:
Status:No Display Connected

Memory:
Memory Slots:

ECC: Disabled

BANK0/DIMM0:

Size:32 MB
Type: DDR2 SDRAM
Speed:667 MHz
Status:OK
Manufacturer:N/A
Part Number:N/A
Serial Number:N/A

BANK1/DIMM1:

Size:32 MB
Type: DDR2 SDRAM
Speed:667 MHz
Status:OK
Manufacturer:N/A
Part Number:N/A
Serial Number:N/A

Power:
Battery Information:

Model Information:
Serial Number:
-
-LION
-

Manufacturer:

Device name:

Pack Lot Code:0000
PCB Lot Code:0000
Firmware Version:0000
Hardware Revision:0000
Cell Revision:0000
Charge Information:
Charge remaining (mAh):2259
Fully charged:No
Charging:No
Full charge capacity (mAh):3690
Health Information:
Cycle count:0
Condition:Normal
Battery Installed:Yes
Amperage (mA):-1431
Voltage (mV):10956

System Power Settings:

AC Power:
System Sleep Timer (Minutes):53
Disk Sleep Timer (Minutes):10
Display Sleep Timer (Minutes):53
Automatic Restart On Power Loss:No
Display Sleep Uses Dim:Yes
Battery Power:
System Sleep Timer (Minutes):10
Disk Sleep Timer (Minutes):10
Display Sleep Timer (Minutes):2
Current Power Source:Yes
Display Sleep Uses Dim:Yes
Reduce Brightness:Yes

Hardware Configuration:

UPS Installed:No

AC Charger Information:

Connected:No
Charging:No

Serial-ATA Bus:

WDC WD1600BEVT-22ZCT0:

Capacity:160.04 GB (160,041,885,696 bytes)
Model:WDC WD1600BEVT-22ZCT0
Revision:11.01A11
Serial Number: WD-WXE509R2C476
Removable Media:No
Detachable Drive:No
BSD Name:disk0
Protocol:ata
Unit Number:0
Socket Type:Serial-ATA
Partition Map Type:GPT (GUID Partition Table)
S.M.A.R.T. status:Verified
Volumes:
Macintosh HD:
Capacity:159.7 GB (159,697,911,808 bytes)
Available:150.74 GB (150,744,125,440 bytes)
Writable:Yes
File System:Journaled HFS+
BSD Name:disk0s2
Mount Point:/

USB Bus:

Host Controller Location:Built-in USB
Host Controller Driver:AppleUSBUHCI
PCI Device ID:0x27cb
PCI Revision ID:0x0002
PCI Vendor ID:0x8086
Bus Number:0x7d

Software Tab:

System Software Overview:

System Version:Mac OS X 10.6 (10A432)
Kernel Version: Darwin 10.0.0
Boot Volume:Macintosh HD
Boot Mode:Normal
Computer Name:Jack Adamss Mac
User Name:Jack Adams (Jack)
Secure Virtual Memory:Enabled
64-bit Kernel and Extensions:No
Time since boot:10 minutes

Also If this info is useful on the box it says: MSI U100-804AU

I got Headphone and Bluetooth working.

Headphones using Audieee

Bluetooth by turning it on!

I am looking for some assistance as well, I have a U100. Increased the hard drive to 320, 2gb ram. It does not have bluetooth. I have purchased an Airport Extreme wifi card and I have a retail Snow Leopard retail disc 10.6.

Does anyone have a tutorial or link that I can follow. I would like to run a dual boot of Windows 7 32 bit and OSX or XP and OSX, Would really appreciate feedback with links or feel free to pm me

Thanks
CK on west coast of Canada

Not really a tutorial but I have EVERYTHING (!) in my Wind up and running using the kexts here:
http://www.trick77.com/2009/11/08/sn...msi-wind-u100/

Even SpeedStep is working which conserves a whopping slice of battery time comparing to running the CPU at 100%!

I'm running 10.6.2 on my MSI Wind U100 now. I just made a backup of the old mach_kernel and copied it to the root-directory after 10.6.2 was installed. You'll need to boot in single user mode (with your installation USB stick) and mount the internal hard drive to replace the kernel.

Sunstar:

Is there a tutorial on replacing the 10.6.2 with the 10.6.1 kernel?

I got everything working but the internal mic. Still working on it.

Oh and sunstar
Did those kexts get your internal mic working?

Internal mic doesn't work... there's just static noise. But it is crap anyway for VOIP (it's humming badly!). You better use some cheap USB sound adapter.

There's a how-to for replacing the kernel:
trick77.com MSI Wind U100 netbook: How to update to 10.6.2

My Bad! Lol! Posted twice!

I found a easy you use guide. Assuming you have a bootable cd with chameleon bootloader installed:
http://www.trick77.com/2009/11/14/ms...update-10-6-2/

Lol! Same link as sunstar!