Hackint0sh - Kernel / Kext (Driver) Support

Hackint0sh - Kernel / Kext (Driver) Support http://www.hackint0sh.org// Support for very core stuff like kernel and kext (driver) en Sat, 21 Nov 2009 02:54:15 GMT vBulletin 15 http://www.hackint0sh.org/ogenzen/misc/rss.jpg Hackint0sh - Kernel / Kext (Driver) Support http://www.hackint0sh.org// Incorrect Resolution. http://www.hackint0sh.org//showthread.php?t=98466&goto=newpost Wed, 18 Nov 2009 16:06:36 GMT How do I get my Hac to start using my moniter's actual native resolution.. when I go to System Preferences/Display there's only one resolution avalible and it's much too small. I think my native resolution is 1280x1024, but Mac says it's 1024x768, so the screen seems stretched and distorted. I've tried that program that is supposed to program custom resolutions into your Mac, but it didn't work at all. Any suggestions? If you need any information, I'll be more than happy to share anything that can help get this fixed. ]]> Kernel / Kext (Driver) Support CHICKENBUISCUT http://www.hackint0sh.org//showthread.php?t=98466 distorted display http://www.hackint0sh.org//showthread.php?t=98362&goto=newpost Wed, 18 Nov 2009 00:54:56 GMT I often get a distorted display when using Safari, where all text becomes unreadable. Just now, while loading a page in Safari, the display became... I often get a distorted display when using Safari, where all text becomes unreadable. Just now, while loading a page in Safari, the display became unresponsive and wouldn't let me click anything for almost a minute ... when it came back the text all over the screen was distorted (as if it were smudged or behind water). I see many entries like the following in system.log:

Code:

Nov 17 19:29:02 myhost kernel[0]: NVDA(OpenGL): Channel exception!  status = 0xffff info32 = 0x3 = Fifo: Unknown Method Error

Nov 17 19:29:02 myhost kernel[0]: 0000000b

Nov 17 19:29:06 myhost kernel[0]: NVDA(OpenGL): Channel exception!  status = 0xffff info32 = 0xd = GR: SW Notify Error

There are also many entries like the following in windowserver.log, but none that seem to correspond with the timing of the NVDA errors above:

Code:

Nov 17 19:50:53 [112] kCGErrorFailure: destroyBackingSurface : IOAccelWriteLockSurface = e00002bd

I don't know whether this is a kernel problem (9.8.0, based on Voodoo) or graphics problem (NVKush, GeForce 7600 GT), or if they're two separate problems ... or how to go about checking or fixing this. ]]> Kernel / Kext (Driver) Support deesto http://www.hackint0sh.org//showthread.php?t=98362 VGA rom dump is 0 bytes?! http://www.hackint0sh.org//showthread.php?t=98263&goto=newpost Tue, 17 Nov 2009 19:26:16 GMT Hi all,

After a week of reading, trying, getting errors and swearing. I just had to ask here for help.
I'm trying to get some dual-screen action on my laptop and Samsung Syncmaster.

It's a:
HP Dv5-1150 ED
nVidia 9200m GS, 256 MB
4 gigs of memory
And so on.

Got everything working just fine,even Qe/Ci is working perfect. But no dual-screen support so far.
So did some searching and lots of reading, and found out i had to dump my videocard bios and run it through NVCAP_Maker. So prepared a USB stick to boot DOS, copied nvflash.exe on there along with cwsdpmi.exe.

But it didn't dump. Tried 4 different versions of Nvflash but no luck. Keep ending up with a dump of 0 bytes.
It also gives an error, version: invalid. And with older versions of nvflash I get errors but it gives a ID, EEPROM ID=20,00f. Nvflash 557 says there is one adapter: NB9m-GE?

Really hope someone here can help me out.

Greetings, Byte ]]> Kernel / Kext (Driver) Support byteworkz http://www.hackint0sh.org//showthread.php?t=98263 Safe Mode Video? http://www.hackint0sh.org//showthread.php?t=98206&goto=newpost Tue, 17 Nov 2009 14:36:53 GMT I just did an install. It is a laptop with an NVidia chipset, and seems to be using an "NVDARWIN" driver or something.

The problem is, the driver doesn't quite work and the video only works (correctly) when I am Safe mode.

I don't have a problem with this, however, when I boot in "safe" mode, by keyboard doesn't work.

So my question is - is there a way I can tell what video driver it is using (in a "normal" boot, and for a "safe" boot) - and have it use the "safe boot" driver for a "normal boot" too - so I can get my keyboard to work, too? ]]> Kernel / Kext (Driver) Support bkgoodman http://www.hackint0sh.org//showthread.php?t=98206 Eathernet Drivers for Toshiba Satellite M505 Laptop - help please http://www.hackint0sh.org//showthread.php?t=97918&goto=newpost Sun, 15 Nov 2009 17:06:18 GMT Ok so yesterday I was able to get the iATOKOS v7 to install on the laptop that's listed in the subject line. I had to disable one of the cores to get it to work; which is fine. However, when I go to boot it up to use it it looks up. So I ran it in verbose mode to see where it hangs up and it appears it stops at the part where it is trying to load the ethernet information.

Is there a way around this so the OS will load. I don't care if the eathernet actually works or not. This laptop does not need to have online access. Just a working version of Leopard is all I need.

Any ideas? ]]> Kernel / Kext (Driver) Support hotrod http://www.hackint0sh.org//showthread.php?t=97918 Wireless PCI http://www.hackint0sh.org//showthread.php?t=97873&goto=newpost Sun, 15 Nov 2009 00:12:00 GMT hi , i just installed iatkos v7 on my desktop pc , and i got almost everything working ,except for wirless internet got a linksys pci card , but its... hi , i just installed iatkos v7 on my desktop pc , and i got almost everything working ,except for wirless internet
got a linksys pci card , but its not working , somehow i see conections on network (no ethernet used)
so im wondering if someone got a driver for it , or a way to configure it?
cause it appears conected and with automatic ip
so im confused :spinme
even tho i cant open things on safari

i just need wireless so i can start using real Mac-ish progs

thanks ]]> Kernel / Kext (Driver) Support Rorix http://www.hackint0sh.org//showthread.php?t=97873 ATI Mobility Radeon HD 4650 Problem? http://www.hackint0sh.org//showthread.php?t=97779&goto=newpost Sat, 14 Nov 2009 01:18:51 GMT Hello,

I've just installed iAtkos v7 on my HP laptop. The installation was fine but after i boot up passed the boot logo (the :pie:), my screen goes back. I've tried plugging in an external moniter and using boot flags, but the screen just stays black :( .

Is there anyway to get it working?

Also, when I boot into single-user mode, I'm unable to type anything with the keyboard on my laptop. Do i need an extra driver for my keyboard?

Specs (HP Pavilion DV6 2016ax):
AMD Turion X2 Dual-Core Mobile Processor RM-74 (2.2GHz, 1MB L2 Cache)
320GB (5400RPM) Hard Drive
4096MB DDR2 SDRAM
ATI Mobility Radeon HD 4650 Graphics with 1024MB DDR3 dedicated graphics memory

Thanks :) ]]> Kernel / Kext (Driver) Support chew http://www.hackint0sh.org//showthread.php?t=97779 kernal banic befor installition !!!?!?!?!?1 plz HEEEELP http://www.hackint0sh.org//showthread.php?t=97233&goto=newpost Wed, 11 Nov 2009 12:53:23 GMT hello ! i was mad of the kernal panic when i booting from the installation disc its says kernal panic how can it do that before i start... hello !

i was mad of the kernal panic when i booting from the installation disc

its says kernal panic how can it do that before i start installation !!!:mad:

do any one can help me i will be thankfull for him and u O:)

so plz help me

i using the iPC 10.5.6 ]]> Kernel / Kext (Driver) Support Smego http://www.hackint0sh.org//showthread.php?t=97233 Intel GMA 950 (Device ID 0x27a2) on VGN C1S http://www.hackint0sh.org//showthread.php?t=97215&goto=newpost Wed, 11 Nov 2009 06:47:01 GMT Dear Friends, After reading alot information and learning many cool stuff - I got OSX 10.5.7 fully working on my Sony Vaio VGN-C1S - i also... Dear Friends,

After reading alot information and learning many cool stuff - I got OSX 10.5.7 fully working on my Sony Vaio VGN-C1S - i also changed the wifi card to have a broadcom one installed!

However I am having a nightmare in managing to install the Intel GMA 950 (Device ID 0x27a2) to have full QE support which I need to have iworks 09 work! The video card is only using software support.

I have tried installing some kexts for the 950, which i found online, but to no results - since when the laptop restarts I am left with a number vertical lines on a white/grey background. I think I have formated this laptop around 10 times in 3 days.

Any help pls? Any patches/kexts or fixes?

Kindly note I have tried the following three proposed solutions:

1.

* Using Drivers Includded in DellEFI 1.2a5. Or upgrade base Kalyway 10.5.2 installation with "iDeneb.upgrade 10.5.7 by darwinux".
* Before rebooting, I reinstalled the appleintelintegratedframebuffer kext using System/Installation/Packages/Patches/GMA950_appleintelintegratedframebuffer.pkg from the Kalyway 10.5.2 CD.
* Otherwise I got a blue screen on reboot with any of the 3 kernel choices on iDeneb upgrade. The iDeneb upgrade should include this package to simplify upgrades for us GMA 950 folk.
* During your Kalyway 10.5.2 installation make sure to pick the Intel 950 driver in custom options, otherwise you will get the same blue screen treatment.

(from Wiki/index.ph...5.7 - OSx86)

2.
Solved!!

Just re-installled my intel D945GCPE (GMA950 0x2772) with iAtkos 5i using stock kernel and stock drivers and EFI string for intel enabled.. I did this even though I knew it wouldnt give true quartz extreme it only says its supported in the profiler but doesnt actually work.. this might not be necessary but I did it anyway..

Then immediately installed 10.5.7 combo update.. The after the restart the system fails to boot completely but automatically reboots again this time successfully.. not sure if this is normal but it happened the first time I tried updating also.. anyway the system is now 10.5.7..

Now to fix the GMA950 i installed this AppleIntelIntegratedFramebuffer.kext using OSX86Tools.. then rebooted once more.. on startup I had real quartz extreme acceleration and full resolution changing ability.. I havnt noticed any artifacts as yet and all applications seem to be running as they should be..

I dont know where I got this kext from as I've downloaded a million kexts and driver bundles and packages etc in my efforts to get quartz extreme working again but whoever supplied this driver thank you so much..

I've also attached the stock GMA950 (10.5.7) kexts for those that need it but if you have tried as many other kext packages as I have you might be better off with a clean install as my experience was that some packages install other kexts that might give false positives in the system profiler..

Hope this helps the many others like me who struggled getting quartz extreme back after 10.5.7

(from 10.5.7 GMA950 Quartz Extreme issue - InsanelyMac Forum)

3. I also tried this this morning:

http://www.insanelymac.com/forum/ind...=#entry1229067

"Sorry for my English. smile.gif

0. Stamina Mode (on GMA950), in BIOS turn ON LCD SCREEN EXPANSION

1. Used 10.5.7 iDeneb v1.5

2. On setup NO VIDEO driver selected.

3. after install and boot, deleted all video kexts from /sys/lib/extensions if any, including appleintelframebuffer.kext and all AppleintelGMA950***, NV***, ATI***, GF***

4. NO RESTART

5. Use KextHelper to intsall attached kexts. (gma950 from 10.5.7. and a AppleIntelIntegratedFrameBuffer.kext from 10.4.8 or 10.4.9, don't know for sure)

6. Restarted and that's it! 1280*800, QE/CI Working on internal screen, no artefacts for now."

But once I started the vaio, all I saw was once again vertical lines and garbage! :-(

I don't know waht else to try pls help!

:spinme does not seem to work apart from software enabled!

Please help! ]]> Kernel / Kext (Driver) Support frankbalzan http://www.hackint0sh.org//showthread.php?t=97215 wifi not working on swapped broadcom nic -eee 100ha ideneb 1.5.6 http://www.hackint0sh.org//showthread.php?t=97102&goto=newpost Tue, 10 Nov 2009 17:12:15 GMT Read most of the threads and I could not find an answer that would work. I used the 1005he install to get my 1005ha to 1.5.6 I swapped my... Read most of the threads and I could not find an answer that would work.

I used the 1005he install to get my 1005ha to 1.5.6

I swapped my atheros wifi card with a dell one I got off the net : Broadcom - bcm94312mcg. Tested it on windows XP dual partition and it works as a charm.

Osx seems to not detect the card at all however. I booted with -v -f and I see the following message:

InterfaceNamer: no network interfaces, could not update platform UUID

Tries installing all kexts again, tried installing airport but it didn't work so I tried it with pacifist manually. I am at a loss ]]> Kernel / Kext (Driver) Support kryo http://www.hackint0sh.org//showthread.php?t=97102 <![CDATA[Vanilla kernel doesn't work on my pc (kalyway)]]> http://www.hackint0sh.org//showthread.php?t=96930&goto=newpost Mon, 09 Nov 2009 19:16:45 GMT Hi, I am new to osx86 and I am able to get kalyway 10.5.2 to work on my pc with 9.2 sleep kernel.. I also tried 10.5.6 iPC distribution, but it... Hi,
I am new to osx86 and I am able to get kalyway 10.5.2 to work on my pc with 9.2 sleep kernel..

I also tried 10.5.6 iPC distribution, but it wasn't working and everytime I try to install vanilla kernel, everything stop working.

I've been able to install 10.5.3 update of kalyway with vanilla kernel 9.3 but I had to do update -v two times or more before I had leopard to start and it was starting on darwin 9.2 kernel (every boot, I had to type update -v or it was rebooting, even -x wasn't working). I tried to install 10.5.5 combo update from apple and the installation was interrupted at 12% and the computer was freeze, I had to reboot it with reset button and it doesn't work now (even with -x or update -v).

I would like to know if it is possible to update to 10.5.8 without vanilla kernel? Or is it possible to get vanilla kernel to work?

Thanks!

My config:

core 2 duo E7300 2.66ghz
geforce 7300GT (sparkle)
pc chips P53G
Seagate 250gb PATA ]]> Kernel / Kext (Driver) Support macos http://www.hackint0sh.org//showthread.php?t=96930 About this mac http://www.hackint0sh.org//showthread.php?t=96468&goto=newpost Fri, 06 Nov 2009 14:40:43 GMT Could someone plz help me with this problem!!!! I updated with the combo pack from 10.5.6 to 10.5.8, and now in my system profiler its says, There... Could someone plz help me with this problem!!!!
I updated with the combo pack from 10.5.6 to 10.5.8, and now in my system profiler its says, There was an error while gathering this information. Is there anyway i can fix this proble?
My Specs are:
* Hp Pavilion
* IPIBL-LB
* Mod BIOS 5.23 ]]> Kernel / Kext (Driver) Support maine http://www.hackint0sh.org//showthread.php?t=96468 Can work GT 220 on snow leopard? http://www.hackint0sh.org//showthread.php?t=96449&goto=newpost Fri, 06 Nov 2009 11:45:14 GMT Does the GT 220 on snow leopard? and if yes work with two monitor?
Because i have a 2 monitor 20' side by side
Thank you.

Mario from Italy ]]> Kernel / Kext (Driver) Support tengo famiglia http://www.hackint0sh.org//showthread.php?t=96449 firewire support for MCP61 chipset http://www.hackint0sh.org//showthread.php?t=95916&goto=newpost Wed, 04 Nov 2009 02:06:24 GMT Running iDeneb Lite 1.6 (10.5.8) with latest Apple software updates. I'd like to get FireWire devices working, but although it seems to supply power to devices, I can't make a "valid" device connection.

System Profiler -> Hardware -> FireWire just says "Warning: Unable to list FireWire devices."

Messages that appear during boot:

Code:

$ grep -i firewire /private/var/log/system.log

Nov  3 20:45:03 localhost kernel[0]: FireWire runtime power conservation disabled. (2)

Nov  3 20:45:04 localhost kernel[0]: FireWire (OHCI) TI ID 8024 PCI now active, GUID 00000ae6ff788717; max speed s100.

Nov  3 20:45:04 localhost kernel[0]: ERROR: FireWire unable to determine security-mode; defaulting to full-secure.

Nov  3 20:46:02 myhost configd[14]: InterfaceNamer:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/HUB0@4/IOPCI2PCIBridge/pci104c,8024@9/AppleFWOHCI/IOFireWireController [1]

Nov  3 20:46:02 myhost configd[14]: InterfaceNamer:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/HUB0@4/IOPCI2PCIBridge/pci104c,8024@9/AppleFWOHCI/IOFireWireController/IOFireWireLocalNode [2]

Installed kexts:

Code:

$ ll /System/Library/Extensions/|grep -i firewire

drwxr-xr-x    3 root  wheel    102 Nov 24  2008 IOFireWireAVC.kext

drwxr-xr-x    3 root  wheel    102 Nov 24  2008 IOFireWireFamily.kext

drwxr-xr-x    3 root  wheel    102 Nov 24  2008 IOFireWireIP.kext

drwxr-xr-x    3 root  wheel    102 Nov 24  2008 IOFireWireSBP2.kext

drwxr-xr-x    3 root  wheel    102 Nov 24  2008 IOFireWireSerialBusProtocolTransport.kext

Is there a kext or something that may get things working? ]]> Kernel / Kext (Driver) Support deesto http://www.hackint0sh.org//showthread.php?t=95916 <![CDATA[iDeneb problem with option "sound"]]> http://www.hackint0sh.org//showthread.php?t=95720&goto=newpost Tue, 03 Nov 2009 09:55:52 GMT I have problem with my sound options. I can't go to sound settings from system preferences. I just click on "sound", its says Loading soud... and it doesn't load :? Pleade help bcus i can't configure my mic. Thanks. ]]> Kernel / Kext (Driver) Support goozzik http://www.hackint0sh.org//showthread.php?t=95720 OSX on DV7 http://www.hackint0sh.org//showthread.php?t=95103&goto=newpost Thu, 29 Oct 2009 20:32:12 GMT Hii all I am new here as you can see just install OSX 10.5.6 from iatkos V7 my note is DV7-1275dx first problem i got to start understanding... Hii all

I am new here as you can see
just install OSX 10.5.6 from iatkos V7

my note is DV7-1275dx first problem i got to start understanding things is to get the keyboard and touchpad working ... can any1 help me?? ]]> Kernel / Kext (Driver) Support trex450 http://www.hackint0sh.org//showthread.php?t=95103 ATI Radeon HD 3430 Problem http://www.hackint0sh.org//showthread.php?t=94894&goto=newpost Wed, 28 Oct 2009 20:10:25 GMT Hello did anyone get this graphic Card working...I need help with installation on my Vaio VGN/NS12m Im new in here so just want to say Hi to all of... Hello did anyone get this graphic Card working...I need help with installation on my Vaio VGN/NS12m
Im new in here so just want to say Hi to all of you.http://www.hackint0sh.org/images/smilies/smile.gif
I got OSX 10.5.7 install,if that help...
Just tell me what i need to do ]]> Kernel / Kext (Driver) Support Basstardo http://www.hackint0sh.org//showthread.php?t=94894 Driver Help On Toshiba A300D http://www.hackint0sh.org//showthread.php?t=94762&goto=newpost Tue, 27 Oct 2009 23:54:46 GMT Hello, i got the OS to start up properly, however I'm missing the audio and the networking (wireless and ethernet), Could you help me ?

The Wireless card: Atheros AR9281 wirelss network adapter
The Ethernet: Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller
The audio: Conexant High Definition Smart Audio

The version I used is iDeneb v1 since is the only one that seemed working, i also tried the 1.4 but failed and the iAtkos v7 but failed, haven't tried the new iDeneb v.1.5 or 1.6. because if i can find the drivers there i would download it. ]]> Kernel / Kext (Driver) Support Kill2bees http://www.hackint0sh.org//showthread.php?t=94762 <![CDATA[asus eee pc 1000HA WLan doesn't work.]]> http://www.hackint0sh.org//showthread.php?t=94750&goto=newpost Tue, 27 Oct 2009 22:09:59 GMT I install ideneb 1.5.1 on my asus eee pc 1000ha, everything work fine expect for wireless lan. anyone know if there a driver for it or how to fix... I install ideneb 1.5.1 on my asus eee pc 1000ha, everything work fine expect for wireless lan. anyone know if there a driver for it or how to fix it?

Thanks ]]> Kernel / Kext (Driver) Support kr1zvnqt http://www.hackint0sh.org//showthread.php?t=94750 Mac OS Leopard 10.5.7 on Toshiba A210-1aO http://www.hackint0sh.org//showthread.php?t=94318&goto=newpost Sun, 25 Oct 2009 12:41:07 GMT Hi! I has installed on my noutebook (Toshiba A210-1aO) iAtkos V7, AMD dual core 2ghz 2gb ram ATI 2600 mobility 512mb (01:00.0 VGA compatible... Hi!
I has installed on my noutebook (Toshiba A210-1aO) iAtkos V7,
AMD dual core 2ghz
2gb ram
ATI 2600 mobility 512mb
(01:00.0 VGA compatible controller [0300]: ATI Technologies Inc M76 [Radeon Mobility HD 2600 Series] [1002:9581])
wi-fi Atheros AR5007EG
(VenID: 168C
DevID: 001C)

---------------
I have trouble with my video card, cant change resolutiuon to 1280x800 only 1024x768 installed driver from RadeonHD osx86 drivers for 2600xt PCI(apple boot list changing not helped.. added key Graphics mode 1280x800x32...).
Now installed this video driver again and have black screen after loading(I think working only external monitor)

______________
Chipset Model: ATI Radeon HD 2600
Type: Display
Bus: PCIe
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 256 MB
Vendor: ATI (0x1002)
Device ID: 0x9581
Revision ID: 0x0000
ROM Revision: 113-B1480A-236
EFI Driver Version: 01.00.236
Displays:
Display:
Resolution: 1024 x 768
Depth: 32-Bit Color
Core Image: Software
Main Display: Yes
Mirror: Off
Online: Yes
Quartz Extreme: Not Supported
QuartzGL: Supported
Display Connector:
_________________

Maybe you can give me solution and links to kext for video card and wi-fi. ]]> Kernel / Kext (Driver) Support igroki http://www.hackint0sh.org//showthread.php?t=94318 ALC883 and USB Fix1.3 installations disappears after reboot http://www.hackint0sh.org//showthread.php?t=94236&goto=newpost Sat, 24 Oct 2009 14:19:38 GMT Hi all,
after a few attempts and a long period of forum readings I've succesfully installed 10.5.5 OSX on my PC.
This is my PC components:
MB= ASUS P5KC (Not the best choice to do that!)
RAM= 4 GB DDR2 800Mhz
CPU= Intel Core 2 Duo E8200 2,6Ghz
GPU= Sparkle Nvidia Geforce 9600GT
Chipset=P35
Audio= Onboard ALC883 6ch+Digital
PATA= Jmicron JMB363
LAN= Onboard Attansic L1 Gb + PCI Realtek RTL8139

Everything is working fine altough, every time I reboot, I have to install again the ALC883 drivers and AppleHDA.kext patched to have the audio works.
Now I've upgraded to 10.5.7 and 2 of my USB plugs on the back of the case stops working. I've found a patch called USB fix 1.3 that fix the issue, but I've to do the same thing I did for the audio. It is still manageable but is there any way to install this audio and USB drivers without the needs to reinstall again every time I have to reboot?
I don't know if is it enough clear, but if you have some questions please ask me... if I'll resolve this 2 minor issues the sysop will be perfect.
Thank you in advance for all you answers

I forgot to say that was Kalyway 10.5.2 DVD installation, upgraded 'til 10.5.7 with Apple Delta updates ]]> Kernel / Kext (Driver) Support TAFKAS http://www.hackint0sh.org//showthread.php?t=94236 Just installed with iDeneb on 1008ha, need help! http://www.hackint0sh.org//showthread.php?t=94203&goto=newpost Sat, 24 Oct 2009 00:46:02 GMT Everything works accept a few things, plz help me out. 1.Battery does not show percentage (shows a X on it) 2.Computer goes to sleep but I cant... Everything works accept a few things, plz help me out.

1.Battery does not show percentage (shows a X on it)

2.Computer goes to sleep but I cant turn it back on from sleep. Need to restart!

3. shotcut keys does not work! ex. vol, brightness etc ]]> Kernel / Kext (Driver) Support hypeber http://www.hackint0sh.org//showthread.php?t=94203 3.24 speed limit http://www.hackint0sh.org//showthread.php?t=94033&goto=newpost Fri, 23 Oct 2009 07:33:15 GMT Hi Guys Great site! I have a hackintosh, that works great but i find i cannot overclock beyond 3.24ghz. if i drop the multiplier to 7.5 i can... Hi Guys
Great site!
I have a hackintosh, that works great but i find i cannot overclock beyond 3.24ghz.
if i drop the multiplier to 7.5 i can get the fsb to push until the processor hits 3.24, but thats all, so the board and memory are happy at high fsb.

when i raise the multiplier to 8.5 i have to drop the fsb until the chip is running 3.24 to get stable.

I can run the chip over 3.24 and get post but i get kernel panic on the grey startup page every time.

Its like the os has a speed limit that wont allow me to go beyond 3.24.

I can overclock this same setup further in windows xp? :confused:

can someone tell me if i am missing a processor limiter disabler kext, or bios setting that will allow me to go further.

thanks

i have
asus p5qvm
8300 2.83
vanilla 5.8
2gb 6400 team dark xtreme ]]> Kernel / Kext (Driver) Support eatdirt http://www.hackint0sh.org//showthread.php?t=94033