ADDITIONS TO THE GUIDE: These additions will not fit in the guide above due to size of the original post.
================================================== ===============================
======
Check iTunes version on computer
================================================== ===============================
It has been reported that older versions of iTunes (7.3.x) will not load the 1.1.1. firmware file. If you have an older version please uninstall iTunes and then install a newer version. My iTunes is 7.4.1.2. If you are unable to locate this particular version then perhaps the following will help:
Windows - 7.4.1. :
http://www.oldapps.com/OldApps/iTune...esSetup741.exe
Mac - 7.4. :
http://www.oldapps.com/OldApps/iTune.../iTunes7.4.dmg
================================================== ===============================
======
Frequently Asked Questions
================================================== ===============================
CAN I USE THIS GUIDE?
Can I follow the guide without the AT&T SIM card?
- Many users have posted success from following these steps without the AT&T SIM card. However, if you have it then I would recommend you use it.
I have downgrade my new 1.1.1 iphone to 1.0.2 and then unlocked with anysim 1.02. can i use this guide to unlock my iphone in 1.1.1? if yes from which part should i start?
- As AnySim 1.02 was used you will need to follow this guide from the beginning.
IMPORTANT: You need to make sure you're using the 03.14.08_G baseband first. To check go to the call keypad and dial '
*3001#12345#*' then press 'Versions'. If you do not see '03.14.08_G' then you will need to downgrade your baseband before beginning this guide.
I have an OTB 1.1.1 downgraded to 1.0.2 and then used anysim 1.1 to unlock. How can I upgrade to 1.1.1 unlocked?
- As AnySim 1.1 was used you can follow this guide from the step :
Restore virgin iPhone to firmware 1.1.1. You can ignore the virginizing steps as they are only for people that used AnySim 1.0 or 1.02
Will this guide work on a phone that was unlocked using iUnlock?
- Yes. Users that have used iUnlock have posted success from following this guide.
I have modified various parts of my 1.0.2 iPhone. Do I have to restore these settings first?
- No. You can follow this guide without putting everything back the way it was. However, please note that your changes will not be transferred when you upgrade. I suggest you check with the owner of each modification as to will it work with 1.1.1.
TERMINAL QUESTIONS
Which Terminal should I install?
- Both
MobileTerminal vsvn198 &
MobileTerminal VT100 vsvn161 have been reported to work.
When Terminal starts I cannot see '#'
- Reinstall the Terminal and BSD Subsystem - Try again
In Terminal I type 'cd' and then 'space' and it says [process completed]
- Reinstall the Terminal and BSD Subsystem - Try again
After running './norz seczone.backup 0x3FA000 0x2000' I only see the following then it stops
# ./norz seczone.backup 0x3FA000 0x2000
geohot's nor dumper
all your norz are belong to us
super fast...just the way i like it
Dumping: A03FA000-A03FC000
Waiting for data...
- Reinstall the Terminal and BSD Subsystem - Try again
After successfully running './norz seczone.backup 0x3FA000 0x2000' should I quit Terminal to copy the backup file to the computer?
- No. This is not required. While I was going through the steps I had the iPhone connected to the computer. I opened Terminal and went through each line. At the point of copying the backup file I just opened iBrickr, copied the file, closed iBrickr and continued with the iPhone. (Nothing was closed).
UPGRADING AND UNLOCKING
While upgrading to 1.1.1. I receive 'iPhone could not be restored. There is not enough memory available'
- Check you have space available on your computer. The ipsw file is basically a compressed zip file and will need to be extracted before running. You can also try removing some 3rd party apps from your iPhone if you have a lot installed.
Safari doesn't seem to crash
- Please check you have an active WiFi connection. Can you see the
http://jailbreakme.com webpage? You should then scroll down to the bottom and click on Install AppSnapp?
While running AnySim 1.1. I click on the red button but it appears to hang
- Please check you have the BSD Subsystem installed.
After running AnySim 1.1. it says 'Unlock Successful' but I have no signal
- Some users say they fixed the problem by replacing the Lockdown file. Try searching the forum for further assistance.
================================================== ===============================
======
Additions from Users that have followed the Guide
================================================== ===============================
01. Putty rather than Terminal during Virginzing steps (from user
zoro66)
If you are uncomfortable typing the virginizing commands directly on the iPhone via Terminal, and would rather type them on a computer, then perhaps your best option would be to use Putty.
For after you have completed the GUIDE:
02. Add EDGE Fix - After applying this fix your EDGE settings should remain after the iPhone is turned off. (from user
abtf2)
01. Go to Installer
02. Click on Sources icon, add the source: http://i.unlock.no (if not already added)
03. Refresh sources
04. Under Unlocking Tools folder, install EDGE Settings Fix
05. Turn iPhone off then back on
03. Add Custom Ringtones in 1.1.1. (from user
abtf2)
See the following post : Better m4a Ringtones - Firmware 1.1.1
http://www.hackint0sh.org/forum/showthread.php?t=13663
================================================== ===============================
================================================== ===============================